Diameter Tape 11502 Series Model: 11502 Series Technical Specification: read more

FAVORIT - Magnetic Stirrer ST0707V2 Brand : Favorit Model : ST0707V2 Cat No : P22005V2 Product Features Ceramic coated aluminum plate material with powder coated aluminum body material. Permissible temp. & humidity at 5°C ~ 40°C, <80%. Max 1,500rpm. Brushless Shade Motor, 20Lit. Technical Specifications Specification P22005V2 Plate Dimension 180 × 180 mm Stirrer Speed Range Max. 1,500 rpm Maximum Stirring Volume (H₂O) 20 Lit. Heating Temperature Max. 400°C Heat Control Fine PWM Controller Speed Control Stepless Heating Output 600 W Motor Type Brushless Shade Motor Permissible Temp. & Humidity 5°C ~ 40°C, <80% Maximum Magnetic Stirrer Bar 50 mm Plate Material Ceramic Coated Aluminum Body Material Powder Coated Aluminum Power Consumption 50 W Dimensions (W × D × H) & Net Weight 180 × 325 × 110 mm, 3.13 kg Packing Size (W × D × H) & Gross Weight 285 × 400 × 170 mm, 3.83 kg Power Supply AC 230V, 50/60 Hz read more

FAVORIT -Hotplate HP0707V2 Brand : Favorit Model : HP0707V2 Cat No : P22002V2 Product Features Ceramic coated aluminum plate material with powder coated aluminum body material. Permissible temp. & humidity at 5°C ~ 40°C, <80%. PWM Control in heat control. Max. 400°C. Technical Specifications Cat No P22002V2 Plate Dimension 180 × 180 mm Stirrer Speed Range Max. 1,500 rpm Maximum Stirring Volume (H₂O) 20 Lit. Heating Temperature Max. 400°C Heat Control Fine PWM Controller Speed Control Stepless Heating Output 600 W Motor Type – Permissible Temp. & Humidity 5°C–40°C <80% Maximum Magnetic Stirrer Bar 50 mm Material (Plate) Ceramic Coated Aluminum Material (Body) Powder Coated Aluminum Power Consumption 620 W Dimensions (W × D × H) & Net Weight 180 × 325 × 110 mm, 3.13 kg Packing Size (W × D × H) & Gross Weight 285 × 400 × 170 mm, 3.83 kg Power Supply AC 230V, 50/60 Hz read more

RANKCONN - Rotary Evaporator – Manual Lifting HR-21M Brand : Rankconn Instruments Model : HR-21M Product Descriptions The rotary evaporator is mainly used for the continuous distillation of large amounts of volatile solvents under reduced pressure. It is especially suitable for concentrating extracts and distilling the receiving solution during chromatographic separation, enabling the separation and purification of reaction products. The basic principle of the rotary evaporator is reduced-pressure distillation, meaning that during solvent distillation under reduced pressure, the distillation flask continuously rotates. Product Features Manual lifting, simple, stable, and reliable structure; laboratory personnel can easily operate it with one hand. LCD display controller, multiple sets of data displayed on one screen, menu-style interface, knob setting: simple, intuitive, and convenient for observation and operation. PID controller allows quick and easy setting of rotation speed, temperature, and time. Unique inclined double-layer serpentine coil design with a cooling area of 0.15 m²; maximum evaporation capacity up to 22 ml/min, ensuring efficient recovery from small to large sample volumes. Double-layer high-efficiency condenser with anti-backflow design; condenser position adjustable. Professional sealing system with high-elasticity PTFE sealing rings, featuring high-temperature resistance, corrosion resistance, and durability; reduces the need for frequent replacement compared with traditional seals, extending service life by more than double. Dual heating modes (water bath/oil bath) with external heating, making the bath pot easy to clean. Technical Specifications Item Specification Model HR-21M Catalogue No. 1015001001 Rotation Speed 20–300 rpm Bath Temperature Range Water bath: RT+5 to 99 ℃Oil bath: RT+5 to 180 ℃ Evaporation Capacity 22 ml/min Speed Setting Knob setting + LCD display Lifting Method Manual lifting Lifting Stroke 130 mm Main Motor Brushless DC Condenser Serpentine condenser, cooling area 0.15 m²; 1 L rotary flask; 1 L receiving flask; TS29/38 flask clamp; S35/20 ball joint Vacuum Sealing Ring PTFE + Teflon coating Water Bath Material Stainless steel inner tank + corrosion-resistant coating Heating Power 1000 W Operating Environment Temp 5–35 ℃ Bath Size (Inner, Ø×H) Ø230 × 130 mm, 4.5 L capacity Dimensions (W×D×H) 482 × 369 × 780 mm Packing Size 660 × 620 × 520 mm Gross Weight 20 kg Packing List No. Item Qty. Remarks 1 Main Unit 1 set   2 Bath Pot 1 set 4.5 L 3 Main Unit Power Cable + Adapter 1 set   4 Bath Pot Power Cable 1 pc   5 Glass Assembly 1 set Includes sample flask, receiving flask, condenser, rotary shaft, feeding valve 6 Main & Auxiliary Sealing Rings 1 set 1 main sealing ring, 2 auxiliary sealing rings (1 spare) 7 Clip 1 pc   8 Water Nozzle 3 pcs   9 Fixing Compression Spring 1 pc   10 Fuse 2 pcs   11 Reducing Adapter 2 sets   12 Clamping Nut 1 pc   13 Flask Removing Nut 1 pc   14 Flask Removing Clip 1 pc   15 Spring Collet 1 pc   16 Step-down Hose Barb Adapter 3 pcs   17 Vacuum Gauge 1 pc   18 User Manual 1 copy   19 Warranty Certificate 1 copy   20 Warranty Card 1 copy   21 Certificate of Conformity 1 copy   22 Packing List 1 copy   read more

FLUKE - 1732 & 1734 Series Three Phase Power Measurement Logger Brand : Fluke Model : 1732 & 1734 Series Product Descriptions The Fluke 1732 (without wifi) and 1734 (with wifi) Three Phase Electrical Energy Loggers deliver easy to use three phase power measurement data for discovering sources of electrical energy waste, overloaded circuits and help you perform routine load studies. Discover when and where energy in your facility is being consumed - from the service entrance to individual circuits. Access and share three phase power data remotely with your team via the Fluke Connect® app so you can maintain safer working distances and make critical decisions in real-time, reducing the need for protective equipment, site visits and check-ins. Product Features Key measurements: Automatically capture and log voltage, current, power, power factor, energy and associated values Fluke Connect® compatible: View data locally on the instrument, via Fluke Connect mobile app and desktop software or through your facilities’ WiFi infrastructure Convenient instrument powering: Power instrument directly from the measured circuit Highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance and downstream Measure all three phases: With included 3 flexible current probes Comprehensive logging: More than 20 separate logging sessions can be stored on the instruments. In fact, all measured values are automatically logged so you never loose measurement trends. They can even be reviewed during logging sessions and before downloading for real-time analysis Optimized user interface: Quick, guided, graphical setup ensures you’re capturing the right data every time, and the intelligent verification function indicates correct connections have been made, reducing user uncertainty Bright, colour touch screen: Perform convenient in-the-field analysis and data checks with full graphical display Complete “in-the-field'' setup through the front panel: No need to return to the workshop for download and setup or to take a computer to the electrical panel Fully integrated logging: Connect other Fluke Connect devices to the Fluke 1734 to simultaneously log up to two other measurement parameters, virtually any parameter available on a Fluke Connect wireless digital multimeter or module* Energy Analyze Plus application software: Download and analyze every detail of energy consumption with our automated reporting Technical Specifications Specifications Accuracy Parameter Range Resolution Intrinsic Accuracy at Reference Conditions (% of Reading +% of Full Scale) Voltage 1000 V 0.1 V ±(0.2% + 0.01%) Current: Direct input i17xx-flex 1500 12'' 150 A 0.1 A ±(1% + 0.02%) 1500 A 1 A ±(1% + 0.02%) i17xx-flex 3000 24'' 300 A 1 A ±(1% + 0.03%) 3000 A 10 A ±(1% + 0.03%) i17xx-flex 6000 36'' 600 A 1 A ±(1.5% + 0.03%) 6000 A 10 A ±(1.5% + 0.03%) i40s-EL clamp 4 A 1 mA ±(0.7% + 0.02%) 40 A 10 mA ±(0.7% + 0.02%) Frequency 42.5 Hz to 69 Hz 0.01 Hz ±(0.1%) Auxillary input ±10 V dc 0.1 mV ±(0.2% + 0.02%) Voltage min/max 1000 V 0.1 V ±(1% + 0.1%) Current min/max Defined by accessory Defined by accessory ±(5% + 0.2%) THD on voltage 1000% 0.1% ±0.5 THD on current 1000% 0.1% ±0.5             Intrinsic Uncertainty ±(% of reading +% of range)¹ Parameter Influence quantity iFlex1500-12 iFlex3000-24 iFlex6000-36 i40S-EL 150 A / 1500 A 300 A / 3000 A 600 A / 6000 A 4 A / 40 A Active Power P PF ≥ 0.99 1.2% + 0.005% 1.2% + 0.0075% 1.7% + 0.0075% 1.2% + 0.005% Active Energy Ea PF ≥ 0.99 1.2% + 0.005% 1.2% + 0.0075% 1.7% + 0.0075% 1.2% + 0.005% Apparent power S 0 ≤ PF ≤ 1 1.2% + 0.005% 1.2% + 0.0075% 1.7% + 0.0075% 1.2% + 0.005% Apparent Energy Eap 0 ≤ PF ≤ 1 1.2% + 0.005% 1.2% + 0.0075% 1.7% + 0.0075% 1.2% + 0.005% Reactive power Q 0 ≤ PF ≤ 1 2.5% of measured apparent power Reactive Energy Er 0 ≤ PF ≤ 1 2.5% of measured apparent power Power Factor PF - ±0.025 Displacement Power Factor - ±0.025 DBF/cosϕ - ±0.025 Additional uncertainty in% of range¹ VP-N>250 V 0.015% 0.0225% 0.0225% 0.015% ¹Range = 1000 V x Irange Reference conditions: Environmental: 23 °C ±5 °C, instrument operating for at least 30 minutes, no external electrical/magnetic field, RH <65% Input conditions: Cosϕ/PF=1, Sinusoidal signal f=50 Hz/60 Hz, power supply 120 V/230 V ±10%. Current and power specifications: Input voltage 1 ph: 120 V/230 V or 3 ph wye/delta: 230 V/400 V Input current: I > 10% of Irange Primary conductor of clamps or Rogowski coil in center position Temperature coefficient: Add 0.1 x specified accuracy for each degree C above 28 °C or below 18 °C Electrical Specifications Power Supply Voltage range 100 V to 500 V using safety plug input when powering from the measurement circuit 100 V to 240 V using standard power cord (IEC 60320 C7) Power consumption Maximum 50 VA (max. 15 VA when powered using IEC 60320 input) Efficiency ≥ 68.2% (in accordance with energy efficiency regulations) Maximum no-load consumption < 0.3 W only when powered using IEC 60320 input Mains power frequency 50/60 Hz ±15% Battery Li-ion 3.7 V, 9.25 Wh, customer-replaceable On-battery runtime Four hours in standard operating mode, up to 5.5 hours in power saving mode Charging time < 6 hours Data Acquisition Resolution 16-bit synchronous sampling Sampling frequency 10.24 kHz at 50/60 Hz, synchronized to mains frequency Input signal frequency 50/60 Hz (42.5 to 69 Hz) Circuit types 1-φ, 1-φ IT, Split phase, 3-φ delta, 3-φ wye, 3-φ wye IT, 3-φ wye balanced, 3-φ Aron/Blondel (2-element delta), 3-φ delta open leg, Currents only (load studies) Data storage Internal flash memory (not user replaceable) Memory size Typical 10 logging sessions of 8 weeks with 1-minute intervals and 500 events¹ ¹The number of possible logging sessions and logging period depends on user requirements. Basic Interval Measured parameters Voltage, current, aux, frequency, THD V, THD A, power, power factor, fundamental power, DPF, energy Averaging interval User selectable: 1 sec, 5 sec, 10 sec, 30 sec, 1 min, 5 min, 10 min, 15 min, 30 min Averaging time min/max values Voltage, Current: Full cycle RMS updated every half cycle Aux, Power: 200ms Demand Interval (Energy Meter Mode) Measured parameters Energy (Wh, varh, VAh), PF, maximum demand, cost of energy Interval User selectable: 5 min, 10 min, 15 min, 20 min, 30 min, off Standards Compliance Power IEEE 1459 Interfaces USB-A File transfer via USB flash drive, firmware updates Max. current: 120 mA WiFi File transfer and remote control via direct connection or WiFi infrastructure Bluetooth Read auxiliary measurement data from Fluke Connect® 3000 series modules (requires 1734, or 1732 upgrade option) USB-mini Data download device to PC Voltage Inputs Number of inputs 4 (3 phases and neutral) Maximum input voltage 1000 Vrms, CF 1.7 Input impedance 10 MΩ Bandwidth (-3 dB) 42.5 Hz - 3.5 kHz Scaling 1:1 and variable Measurement category 1000 V CAT III/600 V CAT IV Current Inputs Number of inputs 3, mode selected automatically for attached sensor Input voltage Clamp input: 500 mVrms/50 mVrms; CF 2.8 Rogowski coil input 150 mVrms/15 mVrms at 50 Hz, 180 mVrms/18 mVrms at 60 Hz; CF 4; all at nominal probe range Range 1 A to 150 A/10 A to 1500 A with thin flexible current probe i17XX-flex1500 12'' 3 A to 300 A/30 A to 3000 A with thin flexible current probe i17XX-flex3000 24'' 6 A to 600 A/60 A to 6000 A with thin flexible current probe i17XX-flex6000 36'' 40 mA to 4 A/0.4 A to 40 A with 40 A clamp i40s-EL Bandwidth (-3 dB) 42.5 Hz - 3.5 kHz Scaling 1:1 and variable Auxiliary Inputs Number of inputs 2 Input range 0 to ±10 V dc, 1reading/s Scale factor (available 2014) Format: mx + b (gain and offset) user configurable Displayed units (available 2014) User configurable (7 characters, for example, °C, psi, or m/s) Wireless Connection Number of inputs 2 Supported modules Fluke Connect® 3000 series Acquisition 1 reading/s Environmental Specifications Operating temperature -10 °C to +50 °C (14 °F to 122 °F) Storage temperature -20 °C to +60 °C (-4 °F to 140 °F), with battery: -20 °C to +50 °C (-4 °F to 122 °F) Operating humidity 10 °C to 30 °C (50 °F to 86 °F) max. 95% RH 30 °C to 40 °C (86 °F to 104 °F) max. 75% RH 40 °C to 50 °C (104 °F to 122 °F) max. 45% RH Operating altitude 2000 m (up to 4000 m derate to 1000 V CAT II/600 V CAT III/300 V CAT IV) Storage altitude 12,000m Enclosure IP50 in accordance with EN60529 Vibration MIL-T-28800E, Type 3, Class III, Style B Safety IEC 61010-1 IEC Mains Input: Overvoltage Category II, Pollution Degree 2 Voltage Terminals: Overvoltage Category IV, Pollution Degree 2 IEC 61010-2-031: CAT IV 600 V / CAT III 1000 V Electromagnetic compatibility EN 61326-1: Industrial CISPR 11: Group 1, Class A Korea (KCC): Class A Equipment (industrial broadcasting and communication equipment) USA (FCC): 47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103 Temperature coefficient 0.1 x accuracy specification/°C General Specifications Color LCD display 4.3-inch active matrix TFT, 480 pixels x 272 pixels, resistive touch panel Warranty Instrument and power supply: Two-years (battery not included) Accessories: one-year Calibration cycle: two-years Dimensions Instrument: 19.8 x 16.7 x 5.5 cm (7.8 x 6.6 x 2.2 in) Power supply: 13.0 x 13.0 x 4.5 cm (5.1 x 5.1 x 1.8 in) Instrument with power supply attached: 19.8 x 16.7 x 9 cm (7.8 x 6.6 x 3.5 in) Weight Instrument: 1.1 kg (2.5 lb) Power supply: 400 g (0.9 lb) Tamper protection Kensington lock slot i17xx-flex 1500 12'' Flexible Current Probe Specifications Measuring range 1 to 150 A ac/10 to 1500 A ac Nondestructive current 100 kA (50/60 Hz) Intrinsic error at reference condition* ±0.7% of reading Accuracy 173x + iFlex ±(1% of reading + 0.02% of range) Temperature coefficient over operating temperature range 0.05% of reading/°C 0.09% of reading/°F Working voltage 1000 V CAT III, 600 V CAT IV Probe cable length 305 mm (12 in) Probe cable diameter 7.5 mm (0.3 in) Minimum bending radius 38 mm (1.5 in) Output cable length 2 m (6.6 ft) Weight 115 g Probe cable material TPR Coupling material POM + ABS/PC Output cable TPR/PVC Operating temperature -20 °C to +70 °C (-4 °F to 158 °F) temperature of conductor under test shall not exceed 80 °C (176 °F) Temperature, non-operating -40 °C to +80 °C (-40 °F to 176 °F) Relative humidity, operating 15% to 85% non-condensing IP rating IEC 60529:IP50 Warranty One-year * Reference condition:  Environmental: 23 °C ±5 °C, no external electrical/magnetic field, RH 65% Primary conductor in center position read more

ELITECH - Multi Use Real Time Data Logger RCW3000 / RCW3200 Brand: Elitech Model: RCW3000 / RCW3200 Introduction: The RCW 3000 is a split-type repetitive real-time recorder, consisting of a main unit/gateway and a slave unit. It adopts multiple communication methods such as Lora, 4G, Wi-Fi, etc., and can realize real-time/historical data query, remote alarm push and other functions through the Jingchu Cold Cloud Platform or mobile APP. It can be optionally equipped with slave units with various configurations such as temperature and humidity, door magnet, etc. The maximum transmission distance between the master unit and the slave units can reach 1000m, and the maximum number of master units that can be connected is up to 30. It supports various fixation methods such as self-adhesive, card tray, and hanging holes, and is widely used in various scenarios such as large refrigerated warehouses, frozen warehouses, refrigerated cabinets, cool storage rooms, hospitals, fresh food supermarkets, etc. in various industries. Features: ● Wireless deployment: Main unit: 4G + Wi-Fi, Sub-unit: LoRa. No need for punching holes or wiring. Installation is portable. ● Ultra-long battery life: The sub-device can last up to 12 months. ● Large-scale deployment: Lora communication can reach up to 1000 meters at its best. ● Support for customization: Multiple functions such as 4G/Wi-Fi/Network port/Screen can be customized to meet the requirements in different environments Specifications:   read more

RANKCONN - Digital Rotary Viscometer LVDV-1T, RVDV-1T, HADV-1T, HBDV-1T Brand : Rankconn Instruments Model : LVDV-1T, RVDV-1T, HADV-1T, HBDV-1T Product Descriptions Viscometer adopts high-performance imported microcomputer chips, imported stepping motor and other key components, 5-inch touch screen display operation, program setting, automatic control, timing measurement, automatic scanning and other functions; It can measure the absolute viscosity of Newtonian liquid or the apparent viscosity of non-Newtonian liquid. The instrument has high sensitivity, high precision, accurate and reliable test data, and good repeatability. Product Features 5-inch touch screen operation and display, convenient operation, rich Display Information, and powerful human-computer interaction interface The microcomputer driving technology is adopted, and the imported stepping motor makes the rotation rate accurate, stable and reliable Anti-static housing, metal lifting rod design, and new design of shaft tip ensure the durability of the machine Support the storage of test data and test conditions, with up to 30 groups of data stored With the function of timing measurement, it is very practical for detecting non-Newtonian liquids Automatic conversion of dynamic viscosity and kinematic viscosity (the density value of the test sample needs to be known) With automatic scanning function, the instrument can automatically recommend the appropriate combination of rotator and rotation rate It can automatically display the selected rotor rotation speed test range. If it exceeds the test range, the machine will automatically alarm With a printing interface, it can be directly connected to a micro printer to print various data. A printer is required 0.3 to 100 revolutions Continuously Variable Transmission, which is convenient for analyzing and testing the rheological properties of samples, and the test data supports USB disk export The machine can choose a variety of accessories to meet different measurement needs of customers: PT100 temperature sensor, ULR ultra-low viscosity adapter, SSR small-amount sample adapter, thermostatic bath, printer, DVT upper computer software, viscosity standard solution Technical Specifications Type LVDV-1T RVDV-1T HADV-1T HBDV-1T Test Range (cP) 1* — 2M 100** — 13M 200** — 26M 800** — 104M Rotor L1, L2, L3, L4 R2, R3, R4, R5, R6, R7 Rotation Rate (RPM/min) 0.3 — 100 (Continuously Variable Transmission) Specification Details Control/Display Mode 5-inch colour touch screen Demand Amount of Test Sample 400—500 mL (According to different rotators) Display Information Viscosity, rotor, rotation rate, torque %, measurement time, temperature, shear rate, shear stress Test Accuracy ±1% (Newtonian Fluid FS) Reproducibility ±0.3% Test Data Support storage of 30-group data; Support USB flash disk to export test data Viscosity Curve Support real-time display and measurement of visibility curve Overall Dimensions 300 × 300 × 450 mm (L × W × H) Net Weight 4.5 kg Power Supply Input: AC100V to 230V, Output: DC/DC 12V 2A Power 40W read more

AIGU - Digital Force Gauge ZP Series Brand: Aigu Model: ZP-5, ZP-10, ZP-20, ZP-50, ZP-100, ZP-200, ZP-500, ZP-1000 Technical Specification:   read more

EAST TESTER - Current and Voltage Calibrator ET2715A / ET2715B Brand : East Tester Model : ET2715A / ET2715B Product Descriptions ET2715A,ET2715B Current and voltage calibrator is a high precision, high resolution and high reliability hand-held calibrator which integrates output and measurement of V, mV, mA and HZ signals. The instrument adopts large liquid crystal display with clear reading. It also has adjustable backlight and automatic shutdown function. The instrument can be supplied by DC or AC power supply, and is more convenient to use. Product Features Accuracy : 0.02% or 0.05% Perfect performance on waterproof protection : IP67 grade In case of connecting 220V with automatic over voltage protection function. With manual stepping, automatic stepping and 0 ~ 100% output of phase step and ramp function LED with white backlight Source of voltage, current and frequency. Measure of voltage, current, loop current and frequency. Manual stepping and automatic stepping and ramping. Measurement Index Function Range Accuracy(% Reading+counts) ET2715A ET2715B DC mA 0-24.000mA 0.02%+2 0.05%+2 DC V 0~30.000V 0.02%+2 0.05%+2 DC mV -15.000mV~80.000mV 0.02%+2 0.05%+2 80.000mV~125.00mV   Frequency 1.000Hz~99.999Hz   0.01%+1   0.02%+1 1000.0Hz~9999.99Hz 10.000kHz~99.999kHz Output Index   Function Range Accuracy (ET2715A) Accuracy (ET2715B) DC mA (Active/Passive) 0 – 24.000 mA 0.02% + 2 0.05% + 2 DC V 0 – 10.000 V 0.02% + 2 0.05% + 2   DC mV -15.000 mV – 99.999 mV   0.02% + 2   0.05% + 2 100.00 mV – 125.00 mV     Frequency 0.20 Hz – 200.00 Hz     0.01% + 1     0.02% + 1 200.0 Hz – 2000.0 Hz 2.000 kHz – 20.000 kHz read more