ASA - Linear Arm 90 Degree Tools Support Stand TSS-200QA Brand : ASA Model : TSS-200QA Preface   Generally, when using electric and pneumatic screwdrivers to lock screws, there will be a reaction force applied to the operator's arm, when the torque is less than 20kgf-cm, the bare hand can also bear this reaction force, when the torque exceeds 20kgf-cm, it is necessary to use the boom to support the electric and pneumatic screwdriver to absorb the reaction force that occurs during locking to avoid arm injury. Features   The standard multi-angle oil and pneumatic cylinder boom is suitable for locking angled screws regardless of horizontal and verticality. Parallel vertical oil and pneumatic cylinder boom frames, suitable for screws with high horizontal and vertical accuracy. Precautions   Before starting to assemble and operate the ASA Torque Arm Tool Support System, please be sure to read the following operating manual first. Regardless of the circumstances, if electrical wires or air lines are close to running workpieces or machinery, the installers and operators of the equipment should take appropriate precautions to prevent the wires or hoses from being entangled or damaged by the running workpiece. Proper attention will avoid dangerous incidents or personal injuries. Installation and operation instructions   1.Remove the mount from the outer box. 2.Lock it on a working platform with bolts, making sure to keep the mount 1 horizontal, so that the strut 1 (02a) can be at 90 degrees to the working platform throughout the entire process. (Refer to Figure #1) 3.Install the fixing pipe 3, arm 9, and fixing plate 7 into the strut 1 (02a) respectively and fix them with screws. (See Figure #2.) 4.Insert strut 1 (02a) into the mounting seat and lock with the fixing screw. (Refer to Figure #1) 5.The sliding block 11, the sliding block 14, the sliding block 17, the strut 2 (02b), the bearing sleeve 21, the connecting arm 19, the clamping arm 24, etc. are assembled separately, and then fastened with screws together with the arm. (See Figure #3.) 6. After assembly, adjust appropriately according to the actual height of the worktable, and check that each screw is tightened, and pay attention to safety throughout the assembly process. 7.After assembly, adjust appropriately according to the actual height of the worktable, and check that each screw is tightened, and pay attention to safety throughout the assembly process. read more

AP&T - Explosion-Proof Static Meter AP-FY1201 Brand : AP&T Model : AP-FY1201 Product Descriptions The AP-YF1201 Explosion-Proof Electrostatic Voltage Meter is an intrinsically safe explosion-proof testing instrument developed and manufactured by Anping. It uses non-contact measurement technology to minimize the impact of the testing instrument on the static field of the object surface, ensuring measurement accuracy. It can be widely used in industries such as electronics, plastics, chemicals, printing, and optoelectronics. Product Features Comfortable to hold and aesthetically pleasing design. Dual LED precise positioning, accurate detection distance. Wide detection range, high detection accuracy. Comfortable button operation, easy to use. High-definition, all-angle LCD data display. The instrument has intrinsic safety explosion-proof features and can be used in explosive hazardous environments corresponding to or lower than Ex ib Ⅱ B T5 Gb. Technical Specifications Parameter Specification Model AP-YF1201 Measuring Range (KV) 0.001KV – ±2.000KV0.01KV – ±20.00KV0.1KV – ±200.0KV Appearance Color Gray Shell, Gray Key (for first two ranges)Black Shell, Black Key (for last range) Explosion-Proof Rating Ex ib Ⅱ B T5 Gb Detection Accuracy ±10% Detection Distance 25mm ±1.0mm Input Voltage DC 3V (2 × AAA batteries) Operating Current <100mA Power Off Hold power key for 3s or auto shutdown after 180s Working Temperature -18℃ to +50℃ Working Humidity 0–85%RH Dimensions (L × W × H) 141 × 71 × 38 mm Net Weight 146g (including 2 batteries) Gross Weight 359g ±20g (including 4 batteries and accessories) read more

SIMBATOUCH - Controller SBT961A Brand: Simbatouch Model: SBT961A Features: This controller is small in size, double row 6 display, high precision, fast speed, suitable for all kinds of needs to be weighed, load of industrial field. 4-20 ma analog output signal including 10 v and soil. Communication interface support RS-485 and RS-232, standard Modbus protocol support. Support the TEDS intelligent sensor function. Controller with upper limit, the limit, lower limit judge function. Limit line judge function. Specification: read more

AMPROBE - Phase Sequence and Motor Rotation Tester PRM-6 Brand : Amprobe Model : PRM-6 Product Descriptions If you install or connect 3-phase motors and systems, you recognize the importance of verifying the correct motor rotation and wiring phase sequence. Improper connections can cause motors to rotate in reverse direction, potentially damaging the motor and the equipment it is powering. The PRM-6 Motor and Phase Rotation Tester can test the motor rotation of 3-phase systems, and verify 3-phase receptacle wiring and phase sequencing with test leads. An additional advanced feature is wireless motor rotation detection, which senses motor rotation direction without use of test leads. This is particularly useful for fast-running motors when the motor rotation cannot be visually determined or when the drive shaft is not visible Product Features 3-phase wire sequence indication Error displays (missing phase, one input connected to neutral or PE) Non-contact, wireless motor rotation detection on running motors Indicates motor rotation of disconnected motors when spinning the shaft by hand or other means 3-phase to phase voltage up to 700 V Clear backlit LCD display Durable rubber casing for 3 ft. (1 m) drop proof protection Safety: CAT IV 600 V Technical Specifications General Specifications Operating temperature 0°C to 40°C (32°F to 104°C) Operating altitude Up to 2000 m Power AAA battery (2) 3 phase indication LCD Dimensions (H x W x D) 5.43 in x 2.56 in x 1.3 in (13.7 cm x 6.5 cm x 3.3 cm) Weight .38 lb (.17 kg) including battery Dust/water resistance IP 40 Pollution degree 2 Overvoltage category CAT IV 600 V Agency approvals Safety Conforms to EN 61010-1 EN 61010-031 EN 61557-1 EN 61557-7 EMC Conforms to EN 61326-1 Electrical Specifications Rotary field detection Voltage range (frequency) 40 – 700 V (16 – 60 Hz) 50 – 700 V (60 – 400 Hz) Nominal test current < 3.5 mA Non-contract rotary field indication Frequency range 16 – 400 Hz Motor connection (with leads) Voltage range ≥ 1 – 700 V Frequency range 2 – 400 Hz Nominal test current < 3.5 mA read more

AP&T - Ion Blower (2 Fan Overhead) AP-DJ2812 Brand: AP&T  Model: AP-DJ2812 Product Introduction: AP-DJ2812 intelligent control / networking type screen display ion fan using DC de static technology, high air volume fan five-speed speed regulation, stable performance, the output air volume than ordinary fans to improve 1.45 times. With LCD display, with ion self-balancing function, self-balancing range ± 10V, and real-time display of the balance voltage. Features: 1. 8 emitters makes high ion volume and fast decay time; 2. Auto-cleaning when switch on; 3. Default auto-cleaning time every 8 hours, Artificial emitter cleaning maintenance free; 4. Five gears of stable fan speed; 5. LED display shows ID address , fan speed and cleaning time; 6. Duty ratio of positive and negative ion output adjustable to adjust ion balance; 7. Auto balance with range ±10V. 9. Light & Voice alarm when fan default and ion balance abnormal; 10. Remote control ion output When Plate or material surface with high positive static charge, Press “Fan+”“IB-”; When Plate or material surface with high Negative static charge, Press “Fan-”“IB+” 11. Support integrate control by PC, monitor working state of ion blower Specifications: Mod​el AP-DJ2812 Input voltage DC 24V（RJ45 interface）/ Three in one socket（220VAC 50/60Hz） Output voltage DC±4KV → ±6KV Power 21W Ion emission Pulse DC Emitter electrode Tungsten alloy Discharge range 750*550mm（L*W） Air volume ≤ 135CFM*2 Noise Single air outlet≤ 58dBA（1000mm away from the air outlet） Ozone thickness ≤ 0.05ppm（150mm away from the air outlet） Ion balance ≤ |±15V| Discharge speed ≤ 2.5S（450mm away from the air outlet）       Status indicator Power on/clean operation—blue light flashes; Normal work—green light (always under monitoring status); Fan fault alarm—red light always on; Balance voltage exceed alarm-red light flashes； High voltage fault alarm-red light flashes； Infrared debugging/cleaning prompt-blue light flashing Communication method RS485   Signal output RS485（115200bps,8,1,n,n）≥ 20ms Collector open circuit：＜ 50V,100mA Working temperature 0℃ -50℃ Working humidity ＜ 70%RH Dimensions（L*W*H） 510*154*70mm（Ionizing Air Blower body size） Shell material Aluminum powder spraying Installation accessories 1 pair of L-shaped iron powder spraying mounting brackets, 1 pair of bakelite screw handles(M5×8)   Power adapter INPUT：AC100—240V 50/60Hz； （This is preferred for simultaneous power supply) OUTPUT：DC24V 2A（dual RJ45 interface） Net weight(Including power cord and bracket) 2.60KG Warranty 1Year Certification CE read more

ASA - Electric Screwdriver ASA-6000 Series Brand: ASA Model: ASA-6000Q, ASA-6500Q, ASA-6800Q Features: Driven by a low-voltage DC motor, motor by a long service life. The low-voltage screwdriver with a high safety factor, maintain with easy and lower cost. Dual power supply input AC(100-240V), output DC(20-30V), Variable frequency constant voltage function.Torque, temperature and speed are more stable. The power supply capacity increased to 6,0A, enhance the locking power od screwdrive, ensure thr performance of the low-voltage screwdrive in all aspects. Stepless speed regulation + built-in soft start + constant voltage multiple functions design, Trigger start or push to start match different locking methods. Spring balancer + power supply + screwdriver can be used together or separately, with excellent stability and operability more flexible and convenient. read more

LINSHANG - Luminance Meter LS332 Brand: Linshang Model: LS332 Product Introduction: LS332 is a multifunctional luminance meter equipped with a spectral sensor. It is designed to measure luminance, flicker frequency, color rendering index (CRI), and correlated color temperature (CCT) of display screens, backlight panels, lighting fixtures, and similar applications. Additionally, the instrument can display the spectral distribution curve, which helps in identifying the type of backlight source. Features: 1. Supports ultra-high luminance measurement, up to 1 million cd/m. 2. Includes 10mm and 20mm replaceable probes for accurate measurement of all screen sizes. 3. Measures multiple parameters: luminance, spectral curve, flicker, CCT, CRI, etc. 4. Delivers accurate, reliable results approved by authoritative metrology institute. 5. Uses spectral sensor with response matching the V(λ) function. 6. Instant measurement with fast response. 7. Advanced digital probe resists interference, ensuring high accuracy. 8. Offers rich statistics: real-time, max, min, and average luminance. Specifications: read more